Visit Page

 

 

The author is making a number of great observations regarding How to Install a Bathtub as a whole in the content down the page.

Mounting a tub isn't specifically rocket science, yet it does call for strong plumbing, carpentry, and also in some cases, tiling abilities. Changing an old bathtub with a brand-new one is likewise a reasonably tough project. If the old bathtub is easily accessible, the job can move immediately; if you have to open up a wall to remove the old bathtub and place the new bath tub, the task is a lot harder. In either situation, the task is within a house handyman's abilities, although you will certainly need an assistant to move out the old bathtub and embeded in the brand-new one. Make certain you have actually qualified on your own for the job and also are comfortable trying it. Rather than employing a contractor to take over a halfway-completed task, it is better to take into consideration employing one prior to you start. Possibilities are you might require an expert plumber to make tube links.
This short article will certainly help you set up a brand-new bathtub in your shower room if you have actually already gotten a brand-new tub as well as do not need to alter the arrangement of your previous supply of water pipelines.
Your tools as well as product checklist ought to consist of the following:

 

• New Bathtub


• Hammer


• Pipe Wrenches


• Prybar


• Shatterproof glass


• Level


• Pliers


• Adjustable Wrench


• Putty Blade


• Screwdriver


• Cold Knife


• Tape Measure


• Pipe Caps


 

Planning for the Installment

Firstly, the sustaining structure supplied with the bathroom should be fitted (if required) according to the maker's guidelines. Next, fit the taps or mixer to the tub. When suitable the faucet block, it is important to ensure that if the faucet features a plastic washing machine, it is fitted between the bath as well as the faucets. On a plastic bathroom, it is additionally sensible to fit a supporting plate under the taps system to stop pressure on the bath tub.
Fit the flexible tap ports to the bottom of the two faucets making use of 2 nuts and also olives (occasionally provided with the bathtub). Fit the plug-hole outlet by smearing mastic filler round the sink outlet hole, and then pass the outlet with the hole in the bath. Utilize the nut provided by the maker to fit the plug-hole. Check out the plug-hole electrical outlet for an inlet on the side for the overflow pipeline.
Next off, fit completion of the flexible overflow pipe to the overflow outlet. After that, screw the pipe to the overflow face which should be fitted inside the bath. Make sure you use all of the supplied washers.
Connect the catch to the bottom of the waste electrical outlet on the bath tub by winding the string of the waste electrical outlet with silicone mastic or PTFE tape, and also screw on the catch to the electrical outlet. Link all-time low of the overflow tube in a similar manner.The bathroom should now be ready to be fitted in its final setting.

 

 

Removing Old Taps

If you need to replace old faucets with brand-new ones as a part of your setup, after that the first thing you need to do is separate the water. After doing so, activate the faucets to drain pipes any kind of water continuing to be in the system. The procedure of eliminating the existing faucets can be rather troublesome as a result of the limited gain access to that is often the case.
Use a container wrench (crowsfoot spanner) or a faucet device to reverse the nut that attaches the supply pipelines to the faucets. Have a fabric ready for the remaining water that will certainly originate from the pipes. Once the supply pipelines have actually been eliminated, use the very same device to loosen the nut that holds the taps onto the bath/basin. You will certainly require to stop the solitary faucets from turning during this procedure. When the taps have actually been eliminated, the holes in the bath/basin will need to be cleaned up of any type of old securing substance.
Before moving on to fit the brand-new taps, compare the pipeline connections on the old faucets to the brand-new taps. If the old faucets are longer than the brand-new taps, after that a shank adapter is required for the new faucets to fit.

 

 

Installing the Bath tub

Utilizing the two wood boards under its feet, put the bathtub in the called for setting. The wood boards are practical in evenly spreading out the weight of the tub over the area of the boards as opposed to focusing all the weight onto 4 little factors.
The following goal is to make sure that the bathtub is leveled all round. This can be attained by inspecting the level as well as readjusting the feet on the tub until the level reads degree.
To install faucets, fit the bottom of the outermost flexible faucet connector to the proper supply pipe by making a compression sign up with; after that do the exact same for the various other tap.
Activate the supply of water and also inspect all joints and also brand-new pipework for leaks as well as tighten them if essential. Fill the tub as well as also check the overflow electrical outlet as well as the regular outlet for leaks.
Lastly, deal with the bath paneling as described in the maker's user's manual. Tiling and sealing around the tub needs to wait until the bathtub has been utilized at the very least once as this will settle it into its last placement.

 

 

Suitable New Taps

If the tails of the new taps are plastic, after that you will certainly require a plastic adapter to stop damages to the thread. One end of the connector fits on the plastic tail of the faucet as well as the other end provides a link to the existing supply pipes.
If you require to fit a monobloc, after that you will call for minimizing couplers, which attaches the 10mm pipeline of the monobloc to the conventional 15mm supply pipe.
Next off, place the faucet in the installing hole in the bath/basin making certain that the washing machines remain in place between the tap and the sink. Secure the faucet in position with the supplier supplied backnut. When the tap is securely in place, the supply pipes can be attached to the tails of the faucets. The faucets can either be connected by utilizing corrugated copper piping or with regular faucet adapters. The previous kind must be linked to the tap ends first, tightening only by hand. The supply pipes can later be connected to the other end. Tighten both ends with a spanner after both ends have been linked.

 

 

Tiling Around the Tub

In the location where the bathroom fulfills the floor tile, it is essential to secure the accompanies a silicone rubber caulking. This is important as the installation can relocate enough to crack a stiff seal, triggering the water to pass through the wall surface in between the bathroom and the tiling, leading to complications with dampness and possible leaks to the ceiling below.
You can pick from a selection of coloured sealants to blend in your fixtures as well as installations. They are sold in tubes and cartridges, as well as can sealing spaces approximately a width of 3mm (1/8 inch). If you have a larger void to load, you can fill it with twists of drenched paper or soft rope. Bear in mind to always fill up the bath tub with water prior to sealing, to permit the motion experienced when the bathtub remains in use. The sealer can break relatively very early if you do not take into consideration this activity before securing.
Alternatively, ceramic coving or quadrant ceramic tiles can be made use of to edge the bathroom or shower tray. Plastic strips of coving, which are easy to use and cut to dimension, are also easily offered on the marketplace. It is recommended to fit the tiles utilizing waterproof or waterproof sticky and also cement.

 

How to Install or Replace a Bathtub

 

Find Your Dimensions

 

The first step in any bathtub installation or replacement is to select the right size tub for your bathroom. Start by measuring your existing bathtub’s alcove from wall to wall. The standard size for bathtubs is around 5 feet long and 30 or 32 inches wide. Purchase the size that’s closest to your previous tub.

After you’ve measured, you’ll need to figure out what type of tub you need. Face the alcove. If the drain is on the right-hand side, you’ll need a right drain tub. If it’s on the left, get a left drain tub. Easy enough, right?

 

Disconnect the Water Supply and Drain Assembly

 

Before you can start on your removal, make sure that you turn off the tub’s water supply. Some bathrooms have a shutoff valve, but if you don’t see one, you’ll need to turn off the supply at your house’s water main. Once the water’s off, open the valves to release any remaining air in the supply lines.

Then, disconnect the tub drain flange. This process varies based on the type of drain you have, but in most cases, you’ll need a drain flange removal tool to perform this task. If you’re feeling handy, you might be able to use a pair of needle-nose pliers to twist and pull the flange.

Now comes the fun part. In order to disconnect the drain assembly, you’ll need to be able to get to the space underneath the tub. You might need to access the tub drain from a crawlspace or a basement. Don’t forget to take a pipe wrench with you, as you’ll need it to loosen the pipe at the connection.

 

Cut Out the Old Tub

 

After removing the drainpipe assembly, you can take out the old bathtub. Cut a strip above the tub edge in the wall surrounding the bathtub that's about 6 inches in height. The tools you need here may vary depending on the type of wall surround you have in the alcove. If you’re cutting drywall, use a drywall saw and remove the section of the wall all the way down to the studs. If you have tile, you’ll need to use a grinder with a diamond blade to cut through the grout line. Then, use a chisel to remove the individual tiles. Take care here not to cut through any studs.

Find the tub flange. Remove the screws that attach the flange to the studs in the wall. At this point, the tub should be freed from the wall.

Once you’ve removed the flange, use a utility knife to cut away the caulk between the tub and the floor. When this is done, you should be able to lift the tub up and out of the alcove. Keep in mind that, depending on what it’s made of, the old tub could be tremendously heavy. You should plan to have a friend help you move it just in case.

 

Install the New Tub

 

Before you make any adjustments to the area, place the new tub in the alcove to make sure it fits properly and that the tub drain lines up with the P-trap underneath the floor.

Remove it and install a 2 x 4 ledger board. Measure the tub’s flange, then mark that height on the wall. Screw the ledger board to studs in the wall. This will help to support the weight of the tub.

Once the ledger board has been installed, go ahead and secure the drain to the tub. For this step, you’ll need some plumber’s putty. Roll a small amount of putty in your hands and wrap it around the underside of the drain flange. Push the drain into the tub from underneath the tub.

When the drain has been attached, connect the overflow drain. To do this, you’ll place the gasket on the overflow elbow and move it behind the tub. Once that’s on, connect the overflow pipe and the drainpipe, but take care not to overtighten.

 

Secure the Tub

 

After the connections are in, it’s time to set the tub in place. Before you start, make sure the flange lines up with the markings you made in Step 4. Because the ledger board holds the tub in place, it’s important that it matches up. If not, you’ll need to remove it and readjust.

Once your measurements line up, attach the flange to the studs on all three sides of the wall. Please note that you should not screw the flange to the wall. Instead, you should use roofing nails because they won’t rust over time. When the tub is in place, install the baseboard and the molding in front of and around the tub.

Repair and finish off the drywall or tile that you cut in Step 3. If you’re installing a fiberglass bath surround, now’s the time to adhere it to the alcove.

Then, enjoy your tub! While all these steps might seem intimidating, removing and installing a new bathtub is a relatively easy DIY project that can be completed in a single day. And now, when you settle in for your next bubbly soak, you can enjoy your bath without the distraction of a tub in disrepair.

https://www.homeserve.com/en-us/blog/how-to/bathtub-replacement/

 

I recently found that article about How to Install a Bathtub: Install an Acrylic Tub and Tub Surround when browsing on the search engines. Those who enjoyed reading our blog posting kindly remember to pass it around. Many thanks for your time. Kindly stop by our blog back soon.

Schedule Free Estimate